Performing the estimation

Having created all the relevant settings for the physical environment (see Environment Setup) dynamical model (see Propagation Setup), the parameters that are to be estimatd (see Parameter settings), the settings for the observation models (see Observation Model Setup) and the actual observations (simulated or real; see Observation Creation), the estimation can be performed.

Both a full estimation and a covariance analysis are performed by using the Estimator object, which is created as follows:

estimator = numerical_simulation.Estimator(
    bodies,
    parameters_to_estimate,
    observation_settings_list,
    propagator_settings)

where the propagator settings may be single-, multi- or hybrid arc. Creating an Estimator object automatically propagates the dynamics and variational equations for the specific propagator and parameter settings.

Covariance analysis

The settings for a covariance analysis described here can be used to compute the covariance using the compute_covariance() function.

covariance_analysis_output = estimator.compute_covariance(
    covariance_analysis_settings)

where the covariance_analysis_output is an object of type CovarianceAnalysisOutput from which the design matrix, covariance, etc. can be retrieved. During the calculation of the covariance, the columns of the design matrix \(\mathbf{H}\) are normalized (see below), and both the regular and normalized quantities (design matrix \(\mathbf{H}\), covariance \(\mathbf{P}\), inverse covariance \(\mathbf{P}^{-1}\)) can be retrieved. For most applications, the regular (unnormalized) quantities are the ones that are of interest. Use of the normalized quantities should be limited to those applications where a manual inversion is performed.

In addition to the quantities listed above, formal errors and correlations (directly obtained from the unnormalized covariance) can be obtained from the CovarianceAnalysisOutput class.

Normalization

The partial derivative matrix \(\mathbf{H}=\frac{\partial\mathbf{h}}{\partial\mathbf{p}}\) is computed automatically for all observations and parameters, from which the inverse covariance \(\mathbf{P}^{-1}\) is then computed, as described here. However, due to the potentially huge difference in order of magnitude of the estimated parameters (for instance, the Sun’s gravitational parameter, at approximately :math:` 1.3267 cdot 10^{20}` m^3/s^2, and the bias of a VLBI observaion, at \(10^{-9}\) radians), the inversion of the matrix \(\mathbf{P}^{-1}\) can be extremely ill-posed. We partly correct for this problem by normalizing the parameters.

The normalization is achieved by computing a vector \(\mathbf{N}\) (of the same size as the parameter vector \(\mathbf{p}\), such that for each column of the matrix \(\mathbf{H}\), we have:

\[\max_{i}\left| \frac{H_{ij}}{N_{j}}\right|=1\]

That is, the entries of \(\mathbf{N}\) are chosen such that they normalize the corresponding column of \(\mathbf{H}\) to be in the range \([-1,1]\). We denote the normalized quantities with a tilde, so that:

\[\begin{split}\tilde{H}_{ij}=\frac{H_{ij}}{N{j}}\\ \tilde{P}_{ij}=P_{ij}N_{i}N_{j}\end{split}\]

When inverting the normal equations, normalized quantities are always used. Both the normalized and regular quantities can be retrieved from the CovarianceAnalysisOutput class.

Full estimation

Note

To estimate the initial state of a body, its associated ephemeris must be tabulated. When specifying an ephemeris for any of the estimated bodies, convert its type to tabulated using the tabulated_from_existing() setting (for estimated translational dynamics)

Similarly, the settings for a full estimation described here can be used to perform the full estimation using the perform_estimation() function.

estimation_output = estimator.perform_estimation(
    estimation_settings)

where the estimation_output is an object of type EstimationOutput, which (in addition to all information in CovarianceAnalysisOutput) contains information on the estimation process. Note that the covariances etc. that are saved are those from the iteration where the residual was lowest.

The specific additional information that is retained for the EstimationOutput is defined by the define_estimation_settings() function of the EstimationInput class. We note that saving all information from each iteration may not be recommended for larger applications, as the memory consumption that is required may be prohibitive.

After the estimation is finished, the properties of both the environment (in the bodies) and the estimated parameters (in the parameters_to_estimate) are modified as follows:

  • The ephemerides of all propagated/estimated bodies will be set to the propagation results of the last iteration in the estimation. For instance, when estimating the state of body “Delfi-C3”, the (tabulated) ephemeris of this body will be set to contain the numerical results of the last iteration of the estimatiomn

  • The values of the parameter values in the parameters_to_estimate object are those of the last iteration of the estimation. Note that, if the apply_final_parameter_correction parameter to the EstimationInput is set to True, the parameter correction computed at the end of the last iteration (for which the peformance has not been computed) has been used to update the parameters vector

The main results of the estimation are characterized by two quantities: